APRS Track Direct

My position About ☰

reset

HS5TQA-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5TQA-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	VBAT*	IBAT*	TEMP*
1780606034	13.24 V	53 mA	24.97 °C
1780604232	13.24 V	55 mA	24.42 °C
1780602432	13.24 V	52 mA	24.35 °C
1780600632	13.24 V	51 mA	24.31 °C
1780598832	13.24 V	54 mA	24.39 °C
1780597032	13.24 V	51 mA	24.47 °C
1780595232	13.24 V	48 mA	24.58 °C
1780593432	13.25 V	53 mA	24.64 °C
1780591632	13.25 V	47 mA	24.7 °C
1780589832	13.25 V	49 mA	24.6 °C
1780588032	13.25 V	48 mA	24.78 °C
1780586232	13.26 V	47 mA	24.83 °C
1780584432	13.26 V	48 mA	24.74 °C
1780582632	13.27 V	53 mA	24.59 °C
1780580832	13.28 V	52 mA	24.61 °C
1780579032	13.3 V	52 mA	24.58 °C
1780577234	13.32 V	46 mA	24.57 °C
1780575434	13.34 V	49 mA	24.48 °C
1780573632	13.37 V	52 mA	24.59 °C
1780571832	13.4 V	50 mA	24.63 °C
1780571824	13.4 V	51 mA	24.56 °C
1780571824	13.4 V	51 mA	24.56 °C
1780571824	13.4 V	51 mA	24.56 °C
1780571824	13.4 V	50 mA	24.63 °C
1780571824	13.4 V	50 mA	24.63 °C

*Used Equation Coefficients:

VBAT: 0, 0.01, 0

IBAT: 0, 1, -2000

SOLAR: 0, 0.01, 0

SUN: 0, 1, 0

TEMP: 0, 0.01, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)