APRS Track Direct

My position About ☰

reset

VK2GJ-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2GJ-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vbat*	Psys*	Temp*	AirP*
1765015808	3.98 V	112 mW	35.8 degC	98712.5 Pa
1765015481	3.98 V	146 mW	37.5 degC	98700 Pa
1765015107	3.98 V	132 mW	37.1 degC	98687.5 Pa
1765014810	3.99 V	154 mW	38.4 degC	98687.5 Pa
1765014360	3.99 V	122 mW	36.1 degC	98687.5 Pa
1765013683	3.98 V	126 mW	37.1 degC	98662.5 Pa
1765013266	3.98 V	120 mW	35.8 degC	98662.5 Pa
1765012976	3.98 V	146 mW	37.2 degC	98662.5 Pa
1765012652	3.98 V	136 mW	37.3 degC	98662.5 Pa
1765012187	3.98 V	120 mW	34.8 degC	98675 Pa
1765011830	3.98 V	120 mW	35.4 degC	98675 Pa
1765011517	3.98 V	138 mW	36.8 degC	98662.5 Pa
1765011163	3.98 V	124 mW	37 degC	98650 Pa
1765010817	3.98 V	150 mW	37.3 degC	98637.5 Pa
1765010374	3.98 V	108 mW	34.8 degC	98675 Pa
1765010072	3.98 V	144 mW	36.9 degC	98687.5 Pa
1765009699	3.97 V	122 mW	36.6 degC	98750 Pa
1765009338	3.97 V	130 mW	36.6 degC	98762.5 Pa
1765008944	3.98 V	128 mW	35 degC	98650 Pa
1765008616	3.97 V	126 mW	35.9 degC	98600 Pa
1765008306	3.98 V	146 mW	37.4 degC	98575 Pa
1765007881	3.98 V	116 mW	36.2 degC	98537.5 Pa
1765007521	3.98 V	126 mW	36.4 degC	98525 Pa
1765007137	3.97 V	112 mW	35.5 degC	98487.5 Pa
1765006784	3.98 V	130 mW	35.9 degC	98475 Pa

*Used Equation Coefficients:

Vbat: 0, 0.001, 0

Vsol: 0, 0.001, 0

Psys: 0, 2, 0

Temp: 0, 0.1, -100

AirP: 0, 12.5, 500

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)