APRS Track Direct

My position About ☰

reset

VA7VCT Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VA7VCT. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1775942990	11 Volts	24.16 Deg.C
1775942908	11 Volts	23.67 Deg.C
1775942829	11 Volts	23.67 Deg.C
1775942749	11.03 Volts	24.16 Deg.C
1775942671	11 Volts	23.67 Deg.C
1775942590	11 Volts	23.67 Deg.C
1775942508	11.03 Volts	23.67 Deg.C
1775942428	11.03 Volts	23.67 Deg.C
1775942349	11.03 Volts	23.67 Deg.C
1775942271	11.03 Volts	23.67 Deg.C
1775942108	11.03 Volts	23.67 Deg.C
1775942029	11.03 Volts	23.67 Deg.C
1775941950	11.03 Volts	23.67 Deg.C
1775941870	11.03 Volts	23.67 Deg.C
1775941788	11.06 Volts	23.67 Deg.C
1775941708	11.06 Volts	23.67 Deg.C
1775941628	11.06 Volts	24.16 Deg.C
1775941550	11.03 Volts	24.16 Deg.C
1775941388	11.06 Volts	23.67 Deg.C
1775941308	11.06 Volts	23.67 Deg.C
1775941149	11.06 Volts	23.67 Deg.C
1775941069	11.06 Volts	23.67 Deg.C
1775940829	11.06 Volts	23.67 Deg.C
1775940750	11.06 Volts	23.67 Deg.C
1775940669	11.06 Volts	24.16 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0299, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)