APRS Track Direct

My position About ☰

reset

AI0ET-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI0ET-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vaux*	Vmain*	Pi_temp*
1791334902	12.66 Volts	0.01 Volts	55 Deg.C
1791334872	13.49 Volts	0.01 Volts	55 Deg.C
1791334852	13.85 Volts	0.01 Volts	55 Deg.C
1791334841	13.85 Volts	0.02 Volts	55 Deg.C
1791334811	13.87 Volts	0.01 Volts	55 Deg.C
1791334789	13.86 Volts	0.01 Volts	55 Deg.C
1791334778	13.81 Volts	0.01 Volts	55 Deg.C
1791334735	13.83 Volts	0.01 Volts	55 Deg.C
1791334693	13.83 Volts	0.01 Volts	55 Deg.C
1791334643	13.82 Volts	0 Volts	55 Deg.C
1791334594	13.82 Volts	0.01 Volts	55 Deg.C
1791334533	13.79 Volts	0.01 Volts	55 Deg.C
1791334473	13.82 Volts	0.01 Volts	55 Deg.C
1791332224	13.87 Volts	0.01 Volts	53 Deg.C
1791332193	13.96 Volts	0.01 Volts	53 Deg.C
1791332163	13.89 Volts	0.02 Volts	52 Deg.C
1791332132	13.89 Volts	0.01 Volts	54 Deg.C
1791332093	13.89 Volts	0.01 Volts	53 Deg.C
1791332056	13.89 Volts	0.01 Volts	54 Deg.C
1791332027	13.82 Volts	0.02 Volts	53 Deg.C
1791331996	13.83 Volts	0.01 Volts	53 Deg.C
1791331946	13.84 Volts	0.01 Volts	54 Deg.C
1791331925	13.82 Volts	0.01 Volts	53 Deg.C
1791331873	13.78 Volts	0 Volts	54 Deg.C
1791331831	13.82 Volts	0.01 Volts	54 Deg.C

*Used Equation Coefficients:

Vaux: 0, 0.01, 0

Vmain: 0, 0.01, 0

Pi_temp: 0, 1, 0

Value4: 0, 0, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)