APRS Track Direct

My position About ☰

reset

VO2AGO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VO2AGO. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	LiPo*	IndoorTemp*	FreezerTemp*	BatteryTemp*
1732688605	12.53 V	11.1 V	0 C	0 C	50 C
1732688155	12.55 V	11.1 V	0 C	0 C	50 C
1732687705	12.53 V	11.1 V	0 C	0 C	50 C
1732687255	12.54 V	11.1 V	0.1 C	0 C	50 C
1732686805	12.58 V	11.1 V	0.1 C	0 C	50 C
1732686355	12.56 V	11.1 V	0.1 C	0.1 C	50 C
1732685905	12.56 V	11.1 V	0.1 C	0.1 C	50 C
1732685456	12.56 V	11.1 V	0.1 C	0.1 C	50 C
1732685005	12.56 V	11.1 V	0.1 C	0.1 C	50 C
1732684555	12.56 V	11.1 V	0.1 C	0.1 C	50 C
1732684105	12.56 V	11.1 V	0.1 C	0.1 C	50 C
1732683654	12.56 V	11.1 V	0.1 C	0.1 C	50 C
1732683205	12.57 V	11.1 V	0.1 C	0.1 C	50 C
1732682754	12.58 V	11.1 V	0.1 C	0.1 C	50 C
1732682304	12.58 V	11.1 V	0.2 C	0.2 C	50 C
1732681855	12.58 V	11.1 V	0.2 C	0.2 C	50 C
1732680954	12.58 V	11.1 V	0.2 C	0.2 C	50 C
1732680504	12.58 V	11.1 V	0.2 C	0.2 C	50 C
1732680054	12.58 V	11.1 V	0.2 C	0.2 C	50 C
1732679604	12.59 V	11.1 V	0.2 C	0.2 C	50 C
1732679154	12.59 V	11.1 V	0.2 C	0.2 C	50 C
1732678705	12.6 V	11.1 V	0.2 C	0.2 C	50 C
1732678254	12.6 V	11.1 V	0.3 C	0.2 C	50 C
1732677804	12.6 V	11.1 V	0.3 C	0.3 C	50 C
1732677355	12.6 V	11.1 V	0.3 C	0.3 C	50 C

*Used Equation Coefficients:

Battery: 0, 0.01, 0

LiPo: 0, 0.01, 0

IndoorTemp: 0, 0.01, -50

FreezerTemp: 0, 0.01, -50

BatteryTemp: 0, 0.1, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)