APRS Track Direct

My position About ☰

reset

DO5MF-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO5MF-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1791110379	687	5577	7529	3737	4483
1791109778	687	5575	7526	3715	4482
1791109177	687	5575	7526	3695	4483
1791108575	687	5577	7528	3676	4487
1791107975	687	5578	7528	3658	4492
1791107373	687	5576	7529	3637	4479
1791106772	687	5576	7525	3615	4447
1791106172	687	5574	7526	3593	4404
1791105570	687	5575	7528	3573	4401
1791104970	687	5576	7527	3556	4407
1791104370	687	5577	7527	3537	4406
1791103767	687	5576	7526	3521	4393
1791103166	687	5576	7527	3507	4381
1791102566	687	5575	7528	3495	4359
1791101964	687	5574	7525	3483	4348
1791101364	687	5576	7526	3474	4336
1791100764	687	5575	7527	3465	4342
1791100161	687	5577	7525	3457	4345
1791099560	687	5577	7527	3450	4355
1791098960	687	5575	7523	3445	4366
1791098359	687	5574	7525	3441	4365
1791096553	686	5575	7527	3435	4372
1791095951	686	5577	7526	3434	4372
1791095351	686	5581	7527	3432	4370
1791094750	686	5574	7524	3432	4367

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)