APRS Track Direct

My position About ☰

reset

HS4IOO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS4IOO. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	HUM*	BAR*	BAT*
1780611995	100 %RH	800 hPa	4.12 V
1780611395	100 %RH	800 hPa	4.18 V
1780610795	100 %RH	800 hPa	4.18 V
1780610195	100 %RH	800 hPa	4.11 V
1780609595	100 %RH	800 hPa	4.12 V
1780608995	100 %RH	800 hPa	4.18 V
1780608395	100 %RH	800 hPa	4.11 V
1780607795	100 %RH	800 hPa	4.13 V
1780607194	100 %RH	800 hPa	4.18 V
1780606594	100 %RH	800 hPa	4.17 V
1780605995	100 %RH	800 hPa	4.1 V
1780605395	100 %RH	800 hPa	4.11 V
1780604794	100 %RH	800 hPa	4.11 V
1780604194	100 %RH	800 hPa	4.13 V
1780603594	100 %RH	800 hPa	4.18 V
1780602994	100 %RH	800 hPa	4.09 V
1780602394	100 %RH	800 hPa	4.12 V
1780601794	100 %RH	800 hPa	4.13 V
1780601194	100 %RH	800 hPa	4.18 V
1780600594	100 %RH	800 hPa	4.17 V
1780599994	100 %RH	800 hPa	4.1 V
1780599394	100 %RH	800 hPa	4.1 V
1780598794	100 %RH	800 hPa	4.11 V
1780598194	100 %RH	800 hPa	4.13 V
1780597594	100 %RH	800 hPa	4.18 V

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.1, 0

BAR: 0, 0.1, 800

BAT: 0, 0.01, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)