APRS Track Direct

My position About ☰

reset

YB1LZ-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB1LZ-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp.*	Humidity*	Pressure*
1791093469	41 °C	23 %RH	937 hPa
1791091812	40 °C	23 %RH	937 hPa
1791090155	39 °C	24 %RH	938 hPa
1791088498	39 °C	24 %RH	938 hPa
1791086841	38 °C	25 %RH	939 hPa
1791085184	38 °C	26 %RH	939 hPa
1791083527	37 °C	26 %RH	940 hPa
1791081870	37 °C	27 %RH	940 hPa
1791080213	36 °C	29 %RH	940 hPa
1791078555	35 °C	31 %RH	940 hPa
1791076899	34 °C	32 %RH	940 hPa
1791075242	33 °C	35 %RH	940 hPa
1791073585	33 °C	36 %RH	940 hPa
1791071927	32 °C	39 %RH	940 hPa
1791070270	31 °C	40 %RH	939 hPa
1791067770	30 °C	42 %RH	939 hPa
1791066113	30 °C	42 %RH	939 hPa
1791064456	29 °C	43 %RH	939 hPa
1791062799	30 °C	43 %RH	939 hPa
1791061142	29 °C	43 %RH	938 hPa
1791059485	30 °C	42 %RH	938 hPa
1791057827	30 °C	42 %RH	938 hPa
1791056170	30 °C	42 %RH	938 hPa
1791054513	30 °C	41 %RH	938 hPa
1791052856	30 °C	40 %RH	938 hPa

*Used Equation Coefficients:

Temp.: 0, 1, 0

Humidity: 0, 1, 0

Pressure: 0, 1, 0

AllCount: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)