APRS Track Direct

My position About ☰

reset

DL0PCN-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL0PCN-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1775654588	5190	1082	68	1152	7576
1775654466	5192	1049	67	1133	7472
1775654347	5192	1058	70	1120	7348
1775654226	5161	1014	70	1118	7318
1775654105	5191	1063	68	1131	7453
1775653981	5189	1011	66	1136	7529
1775653864	5185	1117	67	1136	7567
1775653743	5191	1079	72	1125	7432
1775653627	5192	971	65	1108	7273
1775653502	5188	1031	67	1086	7099
1775653379	5186	1122	78	1079	7005
1775653258	5184	1135	70	1075	7026
1775653141	5187	1156	71	1067	6984
1775653010	5187	1107	125	1091	6772
1775652890	5186	1119	119	1067	6593
1775652782	5185	1160	69	1023	6412
1775652650	5185	1156	124	1077	6211
1775652529	5184	1143	121	1073	6047
1775652409	5192	1121	121	1066	5871
1775652303	5184	1182	71	1038	5710
1775652169	5186	1109	129	1096	5519
1775652051	5184	1141	127	1087	5396
1775651926	5184	1145	127	1071	5241
1775651806	5184	1161	127	1059	5089
1775651688	5185	1176	122	1047	4957

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)