APRS Track Direct

My position About ☰

reset

HS8AC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS8AC-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TEMP*	HUM*	VBAT*
1791141275	26.74 °C	3.5 %RH	4.2 V
1791140675	26.7 °C	3.7 %RH	4.2 V
1791140063	26.7 °C	3 %RH	4.2 V
1791139463	26.89 °C	2.7 %RH	4.2 V
1791138863	26.87 °C	4.2 %RH	4.2 V
1791138263	26.57 °C	3.8 %RH	4.2 V
1791137663	26.22 °C	3.9 %RH	4.2 V
1791137063	26.37 °C	2.1 %RH	4.2 V
1791136463	26.87 °C	3.9 %RH	4.2 V
1791135863	26.89 °C	3.3 %RH	4.2 V
1791135263	26.89 °C	3.8 %RH	4.2 V
1791134663	27.13 °C	1.6 %RH	4.2 V
1791134063	27.55 °C	0.1 %RH	4.2 V
1791133463	26.94 °C	3.9 %RH	4.2 V
1791132863	27.02 °C	3.2 %RH	4.2 V
1791132263	26.89 °C	3.9 %RH	4.2 V
1791131663	26.92 °C	3.4 %RH	4.2 V
1791131063	27.39 °C	0.9 %RH	4.2 V
1791130463	27.01 °C	2.8 %RH	4.2 V
1791129863	27.11 °C	2.8 %RH	4.2 V
1791129263	26.99 °C	3 %RH	4.2 V
1791128663	26.98 °C	2.9 %RH	4.2 V
1791128063	26.99 °C	2.8 %RH	4.2 V
1791127463	27 °C	2.3 %RH	4.2 V
1791126863	26.94 °C	2.1 %RH	4.2 V

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.1, 0

VBAT: 0, 0.01, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)