APRS Track Direct

My position About ☰

reset

BG5VIG-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BG5VIG-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	CPUFreq*	RF-Rx*	RF-Tx*
1775485457	61 C	80 MHz	191 pkts	67 pkts
1775485157	61 C	80 MHz	139 pkts	49 pkts
1775484857	61 C	80 MHz	91 pkts	35 pkts
1775484557	64 C	80 MHz	42 pkts	20 pkts
1775484257	58 C	240 MHz	1 pkts	7 pkts
1775484067	65 C	80 MHz	58 pkts	24 pkts
1775483767	57 C	240 MHz	0 pkts	6 pkts
1775483639	61 C	240 MHz	2 pkts	8 pkts
1775483521	61 C	240 MHz	0 pkts	6 pkts
1775483285	63 C	160 MHz	432 pkts	145 pkts
1775482985	63 C	160 MHz	377 pkts	128 pkts
1775482685	62 C	160 MHz	330 pkts	112 pkts
1775482386	62 C	160 MHz	279 pkts	94 pkts
1775482086	62 C	160 MHz	241 pkts	77 pkts
1775481786	63 C	160 MHz	192 pkts	60 pkts
1775481485	66 C	160 MHz	151 pkts	47 pkts
1775481185	64 C	240 MHz	114 pkts	35 pkts
1775480886	61 C	240 MHz	66 pkts	22 pkts
1775480587	39 C	240 MHz	0 pkts	1 pkts
1775473082	60 C	240 MHz	0 pkts	6 pkts
1775472875	42 C	240 MHz	2 pkts	2 pkts
1775472452	63 C	240 MHz	0 pkts	6 pkts
1775472294	63 C	160 MHz	145 pkts	68 pkts
1775471996	64 C	240 MHz	115 pkts	52 pkts
1775471708	57 C	240 MHz	76 pkts	36 pkts

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

CPUFreq: 0, 1, 0

RF-Rx: 0, 1, 0

RF-Tx: 0, 1, 0

Digi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)