APRS Track Direct

My position About ☰

reset

W6SRR-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W6SRR-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	DC*	PC Board*	CPU*	Ambient*
1765734409	1354	74.4	33.2	68.7
1765733513	1356	74.5	33.2	68.6
1765732610	1354	74.4	32.7	68.6
1765731710	1356	74.5	32.7	68.4
1765730808	1358	74.4	33.2	68.4
1765729911	1356	74.4	33.2	68.4
1765729010	1356	74.4	33.2	68.4
1765728117	1356	74.4	33.2	68.4
1765727209	1360	74.4	33.2	68.4
1765726313	1354	74.4	33.8	68.6
1765725410	1358	74.3	33.2	68.6
1765724512	1356	74.4	33.2	68.6
1765723608	1365	74.5	33.2	68.6
1765721810	1356	74.6	33.2	68.7
1765720914	1356	74.5	33.8	68.8
1765720009	1358	74.6	32.7	68.8
1765719111	1356	74.8	33.2	68.8
1765718210	1356	74.6	33.2	68.8
1765717310	1356	74.6	32.7	68.8
1765716408	1358	74.9	33.8	68.9
1765715510	1356	74.9	33.2	68.9
1765714609	1356	75	33.2	69
1765713710	1356	75	33.2	69.1
1765712808	1356	75.2	33.8	69.2
1765711911	1356	75.3	33.2	69.4

*Used Equation Coefficients:

DC: 0, 1, 1000

PC Board: 0, 0.1, 0

CPU: 0, 0.1, 0

Ambient: 0, 0.1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)