This is the latest recevied telemetry packets stored in our database for station/object VE3CZO-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Sate* | Temp* | Volt* | Alt* | A5* |
|---|---|---|---|---|---|
| 1769707412 | 12 | 24.8 C | 4.16 V | 100 M | 0 |
| 1769707296 | 12 | 24 C | 4.16 V | 100 M | 0 |
| 1769707178 | 12 | 23 C | 4.16 V | 90 M | 0 |
| 1769707066 | 12 | 21.8 C | 4.16 V | 90 M | 0 |
| 1769706952 | 12 | 20.4 C | 4.16 V | 90 M | 0 |
| 1769706729 | 12 | 18 C | 4.16 V | 90 M | 0 |
| 1769706380 | 12 | 17.6 C | 4.16 V | 90 M | 0 |
| 1769706226 | 12 | 15 C | 4.16 V | 90 M | 0 |
| 1769704563 | 12 | 17.5 C | 4.16 V | 90 M | 0 |
| 1769704232 | 12 | 14.3 C | 4.16 V | 80 M | 0 |
| 1769703619 | 11 | 8.1 C | 4.15 V | 70 M | 0 |
| 1769699015 | 12 | 2 C | 4.15 V | 80 M | 0 |
| 1769698840 | 12 | -1 C | 4.15 V | 90 M | 0 |
| 1769698741 | 12 | -3.3 C | 4.15 V | 80 M | 0 |
| 1769698621 | 12 | -5.5 C | 4.14 V | 90 M | 0 |
*Used Equation Coefficients:
Sate: 0, 1, 0
Temp: 0, 0.1, -50
Volt: 0, 0.01, 0
Alt: 0, 10, 0
A5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)