APRS Track Direct

My position About ☰

reset

KC2G Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC2G. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	BatTemp*	Bat*	Solar*
1765027762	32 deg.F	12.95 V	21.45 V
1765027760	32 deg.F	12.95 V	21.45 V
1765026864	32 deg.F	12.95 V	21 V
1765026861	32 deg.F	12.95 V	21 V
1765025966	32 deg.F	12.95 V	19.9 V
1765025960	32 deg.F	12.95 V	19.9 V
1765025061	32 deg.F	12.95 V	19.8 V
1765024163	31 deg.F	12.95 V	18.8 V
1765024161	31 deg.F	12.95 V	18.8 V
1765023260	31 deg.F	12.95 V	13.6 V
1765022362	31 deg.F	12.95 V	10 V
1765022361	31 deg.F	12.95 V	10 V
1765021462	31 deg.F	12.95 V	10 V
1765021461	31 deg.F	12.95 V	10 V
1765020562	31 deg.F	12.95 V	10 V
1765020561	31 deg.F	12.95 V	10 V
1765019662	31 deg.F	12.95 V	10 V
1765019661	31 deg.F	12.95 V	10 V
1765018762	31 deg.F	12.95 V	10 V
1765018760	31 deg.F	12.95 V	10 V
1765017864	31 deg.F	12.95 V	10 V
1765017861	31 deg.F	12.95 V	10 V
1765016962	31 deg.F	12.95 V	10 V
1765016961	31 deg.F	12.95 V	10 V
1765016060	31 deg.F	12.95 V	10 V

*Used Equation Coefficients:

BatTemp: 0, 0.5, 0

Bat: 0, 0.05, 10

ChgA: 0, 0.05, 0

Solar: 0, 0.05, 10

Chg: 0.002, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)