APRS Track Direct

My position About ☰

reset

VK2RF-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2RF-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Value1*	Value2*
1775539666	13.8 Volts	37.85 Deg.C
1775539598	13.77 Volts	37.37 Deg.C
1775539586	14.12 Volts	37.37 Deg.C
1775539500	13.74 Volts	36.88 Deg.C
1775539464	13.77 Volts	35.41 Deg.C
1775539439	13.98 Volts	34.92 Deg.C
1775539283	13.45 Volts	31.01 Deg.C
1775533128	12.39 Volts	41.77 Deg.C
1775532838	13.89 Volts	43.23 Deg.C
1775532828	13.48 Volts	43.23 Deg.C
1775532793	13.89 Volts	42.74 Deg.C
1775532770	13.74 Volts	42.26 Deg.C
1775532613	13.89 Volts	42.26 Deg.C
1775532582	14.03 Volts	42.74 Deg.C
1775532563	14.12 Volts	42.26 Deg.C
1775532488	13.83 Volts	41.77 Deg.C
1775532361	13.89 Volts	39.32 Deg.C
1775532348	13.65 Volts	39.32 Deg.C
1775532324	13.83 Volts	38.83 Deg.C
1775532275	13.98 Volts	38.34 Deg.C
1775531955	13.65 Volts	33.45 Deg.C
1775526381	13.95 Volts	36.39 Deg.C
1775526189	13.92 Volts	36.39 Deg.C
1775526177	13.77 Volts	35.9 Deg.C
1775526122	13.74 Volts	34.92 Deg.C

*Used Equation Coefficients:

Value1: 0, 0.0293, 0

Value2: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)