APRS Track Direct

My position About ☰

reset

VK2GJ-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK2GJ-6. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vbat*	Psys*	Temp*	AirP*
1791104186	3.93 V	112 mW	27.2 degC	100387.5 Pa
1791102424	4.02 V	118 mW	29 degC	100337.5 Pa
1791102272	3.93 V	114 mW	26.9 degC	100337.5 Pa
1791100606	4.06 V	114 mW	28.1 degC	100287.5 Pa
1791098786	4.06 V	112 mW	27.8 degC	100225 Pa
1791098673	4.06 V	116 mW	27.1 degC	100225 Pa
1791097004	4.06 V	114 mW	28.3 degC	100175 Pa
1791095219	4.06 V	118 mW	29.4 degC	100137.5 Pa
1791095075	3.94 V	120 mW	27.8 degC	100137.5 Pa
1791093433	3.94 V	120 mW	29.5 degC	100125 Pa
1791091629	4.07 V	118 mW	29.4 degC	100100 Pa
1791091477	4.08 V	116 mW	27.7 degC	100100 Pa
1791089813	4.06 V	114 mW	29.2 degC	100100 Pa
1791088028	4.07 V	118 mW	29.4 degC	100100 Pa
1791087876	4.06 V	120 mW	27.5 degC	100112.5 Pa
1791086264	3.95 V	122 mW	29.9 degC	100125 Pa
1791084408	3.94 V	114 mW	28.6 degC	100162.5 Pa
1791084277	4.07 V	116 mW	27 degC	100162.5 Pa
1791082611	4.06 V	118 mW	28.2 degC	100175 Pa
1791080820	4.04 V	120 mW	27.9 degC	100212.5 Pa
1791080679	3.94 V	128 mW	26.3 degC	100212.5 Pa
1791079086	3.93 V	134 mW	28.8 degC	100237.5 Pa
1791077206	4.06 V	128 mW	27.1 degC	100275 Pa
1791077082	4.06 V	124 mW	25.7 degC	100275 Pa
1791075393	3.94 V	124 mW	26.5 degC	100325 Pa

*Used Equation Coefficients:

Vbat: 0, 0.001, 0

Vsol: 0, 0.001, 0

Psys: 0, 2, 0

Temp: 0, 0.1, -100

AirP: 0, 12.5, 500

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)