APRS Track Direct

My position About ☰

reset

DC4HF-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC4HF-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1791092416	1292	5584	7437	3458	3525
1791091514	1292	5588	7441	3465	3503
1791090614	1292	5588	7442	3470	3497
1791089713	1292	5589	7442	3479	3493
1791088812	1292	5584	7438	3488	3492
1791087911	1292	5588	7443	3502	3481
1791087010	1292	5589	7438	3498	3524
1791086109	1292	5587	7440	3527	3481
1791085208	1292	5587	7440	3535	3497
1791084307	1292	5588	7442	3540	3518
1791083405	1292	5587	7440	3547	3523
1791082505	1292	5588	7440	3541	3561
1791081604	1292	5588	7440	3539	3575
1791080703	1292	5587	7441	3534	3581
1791079802	1292	5587	7438	3532	3573
1791078901	1292	5592	7443	3533	3546
1791078000	1292	5586	7439	3541	3520
1791077099	1292	5591	7442	3550	3508
1791076198	1292	5593	7442	3559	3518
1791075297	1292	5592	7442	3567	3525
1791074396	1292	5594	7445	3578	3512
1791073495	1292	5591	7441	3584	3517
1791072594	1292	5594	7439	3596	3503
1791071693	1292	5592	7444	3608	3487
1791070793	1292	5594	7446	3622	3483

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)