APRS Track Direct

My position About ☰

reset

YC0TBU-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YC0TBU-6. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Satellite*	HDOP*	Value3*	Value4*	Value5*
1780970912	25 Sat	0 DOP	0	0	0
1780970781	24 Sat	0 DOP	0	0	0
1780970715	24 Sat	0 DOP	0	0	0
1780970584	25 Sat	0 DOP	0	0	0
1780970518	24 Sat	0 DOP	0	0	0
1780970439	24 Sat	0 DOP	0	0	0
1780970373	24 Sat	0 DOP	0	0	0
1780970363	23 Sat	0 DOP	0	0	0
1780970285	23 Sat	0 DOP	0	0	0
1780970122	24 Sat	0 DOP	0	0	0
1780969990	25 Sat	0 DOP	0	0	0
1780969925	25 Sat	0 DOP	0	0	0
1780969861	25 Sat	0 DOP	0	0	0
1780969793	24 Sat	0 DOP	0	0	0
1780969729	24 Sat	0 DOP	0	0	0
1780969716	24 Sat	0 DOP	0	0	0
1780969695	24 Sat	0 DOP	0	0	0
1780969629	25 Sat	0 DOP	0	0	0
1780969485	23 Sat	0 DOP	0	0	0
1780969340	22 Sat	0 DOP	0	0	0
1780969330	21 Sat	0 DOP	0	0	0
1780969266	20 Sat	0 DOP	0	0	0
1780969187	22 Sat	0 DOP	0	0	0
1780969121	19 Sat	0 DOP	0	0	0
1780968990	24 Sat	0 DOP	0	0	0

*Used Equation Coefficients:

Satellite: 0, 1, 0

HDOP: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)