This is the latest recevied telemetry packets stored in our database for station/object OK2ILA-8. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Voltage* | Car_Int_Temp* | Car_Int_Hum* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1780598372 | 3.85 VDC | 23 C | 57.38 | 8088 | 0 |
| 1780598351 | 3.95 VDC | 23 C | 57.38 | 8088 | 0 |
| 1780598287 | 3.94 VDC | 23 C | 56.97 | 8089 | 0 |
| 1780598223 | 3.94 VDC | 22.9 C | 57.42 | 8087 | 0 |
| 1780598159 | 3.96 VDC | 22.9 C | 57.59 | 8084 | 0 |
| 1780598095 | 3.82 VDC | 22.9 C | 57.64 | 8082 | 0 |
| 1780598031 | 3.82 VDC | 22.9 C | 57.36 | 8087 | 0 |
| 1780597967 | 3.82 VDC | 22.9 C | 58.02 | 8085 | 0 |
| 1780597903 | 3.82 VDC | 22.8 C | 57.89 | 8086 | 0 |
| 1780597839 | 3.83 VDC | 22.8 C | 57.6 | 8086 | 0 |
| 1780597775 | 3.96 VDC | 22.8 C | 58.03 | 8087 | 0 |
| 1780597711 | 3.96 VDC | 22.7 C | 58.41 | 8084 | 0 |
| 1780597647 | 3.95 VDC | 22.7 C | 58.42 | 8086 | 0 |
| 1780597583 | 3.94 VDC | 22.6 C | 58.46 | 8090 | 0 |
*Used Equation Coefficients:
Voltage: 0, 0.01, 0
Car_Int_Temp: 0, 0.1, -50
Car_Int_Hum: 0, 0.01, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)